Diode datasheet readingrectenna, diode selectionReading Diode DatasheetTrying to understand flyback diodes and general diode orientationConstant Voltage model pf Diode circuit analysisWhat is the difference between rectifier/signal diode and zener diode?Should a freewheeling (flyback) diode be used on the coil of a 2-coil latching relay?Rectifiers parametersDifferent Zener Diode SymbolsOutput rectifying diode burning up in LED driverCan I buy an ideal diode? How do I OR two power supplies togetherDiode Array for Full-Wave Rectifier for PoE
Python: return float 1.0 as int 1 but float 1.5 as float 1.5
What's the point of deactivating Num Lock on login screens?
Why is Collection not simply treated as Collection<?>
Infinite Abelian subgroup of infinite non Abelian group example
How do I write bicross product symbols in latex?
What reasons are there for a Capitalist to oppose a 100% inheritance tax?
UK: Is there precedent for the governments e-petition site changing the direction of a government decision?
prove that the matrix A is diagonalizable
Emailing HOD to enhance faculty application
In a Spin are Both Wings Stalled?
What mechanic is there to disable a threat instead of killing it?
intersection of two sorted vectors in C++
Assassin's bullet with mercury
Is there a hemisphere-neutral way of specifying a season?
Why does Kotter return in Welcome Back Kotter
How to take photos in burst mode, without vibration?
Does a druid starting with a bow start with no arrows?
Today is the Center
How to say in German "enjoying home comforts"
Is it unprofessional to ask if a job posting on GlassDoor is real?
Could gravitational lensing be used to protect a spaceship from a laser?
Should I tell management that I intend to leave due to bad software development practices?
Neighboring nodes in the network
What is going on with Captain Marvel's blood colour?
Diode datasheet reading
rectenna, diode selectionReading Diode DatasheetTrying to understand flyback diodes and general diode orientationConstant Voltage model pf Diode circuit analysisWhat is the difference between rectifier/signal diode and zener diode?Should a freewheeling (flyback) diode be used on the coil of a 2-coil latching relay?Rectifiers parametersDifferent Zener Diode SymbolsOutput rectifying diode burning up in LED driverCan I buy an ideal diode? How do I OR two power supplies togetherDiode Array for Full-Wave Rectifier for PoE
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty margin-bottom:0;
$begingroup$
What is difference between single and common cathode configuration? If I want to use 2804 for rectifying, will it act as 2800?
HSMS2800 https://datasheet.octopart.com/HSMS-2800-BLKG-Avago-datasheet-7087620.pdf
diodes rectifier
asked 9 hours ago
Max RockMax Rock
497
$endgroup$
add a comment |
$begingroup$
What is difference between single and common cathode configuration? If I want to use 2804 for rectifying, will it act as 2800?
HSMS2800 https://datasheet.octopart.com/HSMS-2800-BLKG-Avago-datasheet-7087620.pdf
diodes rectifier
asked 9 hours ago
Max RockMax Rock
497
$endgroup$
add a comment |
$begingroup$
What is difference between single and common cathode configuration? If I want to use 2804 for rectifying, will it act as 2800?
HSMS2800 https://datasheet.octopart.com/HSMS-2800-BLKG-Avago-datasheet-7087620.pdf
diodes rectifier
asked 9 hours ago
Max RockMax Rock
497
$endgroup$
What is difference between single and common cathode configuration? If I want to use 2804 for rectifying, will it act as 2800?
HSMS2800 https://datasheet.octopart.com/HSMS-2800-BLKG-Avago-datasheet-7087620.pdf
diodes rectifier
diodes rectifier
asked 9 hours ago
Max RockMax Rock
497
asked 9 hours ago
Max RockMax Rock
497
edited 9 hours ago
Max Rock
asked 9 hours ago
Max RockMax Rock
497
asked 9 hours ago
Max RockMax Rock
497
asked 9 hours ago
Max RockMax Rock
497
497
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
$begingroup$
A 2804 is two 2800's, with their cathodes connected together, put in the same package. You could just use one of them, or you could use both in parallel.
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
$endgroup$
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
|
show 3 more comments
$begingroup$
As you can see in the table, every package has identical single diode specifications.
But your question is "If I want to use 2804 for rectifying, will it act as 2800?"
The temperature rise will be double sharing one package for two diodes.
Answer: Yes for peak currents <=1mA
No , if near Ip=10mA do not use if temp rise exceeds 70'C above worst case board temp.
Although they have identical characteristics, now it means the dual diode package must share the same thermal resistance of;
500°C/W for SOT-23 and 150°C/W for SOT-323
You must work out the temp rise, but it means your DC load must be << 1mA since the diode peak current into a storage cap with 10% ripple will be 10mA
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
$endgroup$
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
);
);
, "mathjax-editing");
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f430728%2fdiode-datasheet-reading%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
A 2804 is two 2800's, with their cathodes connected together, put in the same package. You could just use one of them, or you could use both in parallel.
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
$endgroup$
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
|
show 3 more comments
$begingroup$
A 2804 is two 2800's, with their cathodes connected together, put in the same package. You could just use one of them, or you could use both in parallel.
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
$endgroup$
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
|
show 3 more comments
$begingroup$
A 2804 is two 2800's, with their cathodes connected together, put in the same package. You could just use one of them, or you could use both in parallel.
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
$endgroup$
A 2804 is two 2800's, with their cathodes connected together, put in the same package. You could just use one of them, or you could use both in parallel.
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
answered 9 hours ago
Neil_UKNeil_UK
78.7k285182
78.7k285182
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
|
show 3 more comments
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
That means, if I do not solder one of two terminal side of 2804 diode, it will act as 2800. Am I right?
$endgroup$
– Max Rock
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
These are not power diodes, only small signal, for low current<5mA use. Do you understand Max?
$endgroup$
– Sunnyskyguy EE75
8 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 I am working on project related to rectenna. According to many researches I looked through, mostly used diodes were HSMS 28xx family. I am stuck on choosing right diodes. Most diodes of HSMS 28xx family are obsolete. That is why I am looking for trade-off. What I found HSMS 2804 was not out of stock.
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
@SunnyskyguyEE75 a bit different question, more broadly about my problem I posted here(electronics.stackexchange.com/questions/428821/…)
$endgroup$
– Max Rock
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
$begingroup$
hmm that schematic does not reflect your readings. "circuit gave output 14.5V and 45uA on 200 Ohms load." does not make sense. 45uA on 200 Ohms is 9mV
$endgroup$
– Sunnyskyguy EE75
7 hours ago
|
show 3 more comments
$begingroup$
As you can see in the table, every package has identical single diode specifications.
But your question is "If I want to use 2804 for rectifying, will it act as 2800?"
The temperature rise will be double sharing one package for two diodes.
Answer: Yes for peak currents <=1mA
No , if near Ip=10mA do not use if temp rise exceeds 70'C above worst case board temp.
Although they have identical characteristics, now it means the dual diode package must share the same thermal resistance of;
500°C/W for SOT-23 and 150°C/W for SOT-323
You must work out the temp rise, but it means your DC load must be << 1mA since the diode peak current into a storage cap with 10% ripple will be 10mA
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
$endgroup$
add a comment |
$begingroup$
As you can see in the table, every package has identical single diode specifications.
But your question is "If I want to use 2804 for rectifying, will it act as 2800?"
The temperature rise will be double sharing one package for two diodes.
Answer: Yes for peak currents <=1mA
No , if near Ip=10mA do not use if temp rise exceeds 70'C above worst case board temp.
Although they have identical characteristics, now it means the dual diode package must share the same thermal resistance of;
500°C/W for SOT-23 and 150°C/W for SOT-323
You must work out the temp rise, but it means your DC load must be << 1mA since the diode peak current into a storage cap with 10% ripple will be 10mA
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
$endgroup$
add a comment |
$begingroup$
As you can see in the table, every package has identical single diode specifications.
But your question is "If I want to use 2804 for rectifying, will it act as 2800?"
The temperature rise will be double sharing one package for two diodes.
Answer: Yes for peak currents <=1mA
No , if near Ip=10mA do not use if temp rise exceeds 70'C above worst case board temp.
Although they have identical characteristics, now it means the dual diode package must share the same thermal resistance of;
500°C/W for SOT-23 and 150°C/W for SOT-323
You must work out the temp rise, but it means your DC load must be << 1mA since the diode peak current into a storage cap with 10% ripple will be 10mA
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
$endgroup$
As you can see in the table, every package has identical single diode specifications.
But your question is "If I want to use 2804 for rectifying, will it act as 2800?"
The temperature rise will be double sharing one package for two diodes.
Answer: Yes for peak currents <=1mA
No , if near Ip=10mA do not use if temp rise exceeds 70'C above worst case board temp.
Although they have identical characteristics, now it means the dual diode package must share the same thermal resistance of;
500°C/W for SOT-23 and 150°C/W for SOT-323
You must work out the temp rise, but it means your DC load must be << 1mA since the diode peak current into a storage cap with 10% ripple will be 10mA
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
edited 8 hours ago
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
answered 8 hours ago
Sunnyskyguy EE75Sunnyskyguy EE75
70.4k225102
70.4k225102
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f430728%2fdiode-datasheet-reading%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
